NEW TOOL! The “Re-REEDer” Stamping Die used to Apply DOUBLE-SIDED Reeds to Coin Rings!

New Tool; the coin ring “Re-REEDer”!

Now you can make your finished coin rings stand out by having reeded edges on BOTH sides of your coin ring instead of just one; a look not seen on any coin rings, until now! 😉

A 1921 Morgan Silver Dollar with new “Reeds” applied to the punched edge


The "Re-REEDer"

The “Re-REEDer”


1. Place your coin rings’ un-reeded (punched) edge onto the “Re-REEDER” die after annealing (and quenching) the coin’s edge.
2. Using the hole in the middle of the “Re-REEDer” die as a point of reference, center your coin ring onto the grooves.


3. Next, place the piece of high-impact urethane pad (provided with this tool) over the Mint-reeded side and then put a compression press plate or coin ring Repair Die on top of the urethane pad. This will serve to protect the existing reeds from damage.

4. Line everything up under your hydraulic presses’ ram head, and bring the press ram head down onto the top of the press plate/Repair Die until you begin to feel some resistance. Finally, complete 1-2 full downward strokes with your hydraulic press to imprint the reeded pattern onto the coin ring’s edge.




The result will be a completely uniform pressed-on set of reeds. This tool I initially developed, prototyped and tested back in July of 2016 is the best and most efficient way of accomplishing this task in the shortest amount of time with the greatest amount of consistency.



You can watch a demo video where I “Re-REED” a Morgan Dollar coin rings’ edge by going to my YouTube channel found at: or by pasting the URL below into your internet browser:

Each “Re-REEDer” die is made from a solid piece of the highest quality tool steel that’s been meticulously machined and then carefully hardened for maximum efficiency.

The “Re-REEDer” can also be used to re-apply reeds to any coin that have been damaged. Simply file or sand the old reeds off and re-apply using the same techniques as mentioned above. (Removing the old reeds is best accomplished using a set of Rounding, Finishing and Polishing mandrels that I also offer separately.)

To pick this new tool up, you can visit my Shop page at


You can also click on the direct link below to pick one up:

1.) Start by practicing on clad (non-silver) coins to get a feel for how many presses are required by your particular hydraulic press to imprint the new reeds. Factors such as coin thickness, whether or not you’ve annealed your coin, and the tonnage rating of your hydraulic press are all factors that will determine the outcome of your newly-reeded coin ring edge. If you use a 10, 12, or even a 20-ton hydraulic press, you may only need to complete ½ – 1 full downward stroke to imprint the reeds.

2.) Make sure that the edge you want to Re-REED is as level and smooth as possible. This is best achieved by lightly sanding the edge using circular motions on a piece of sandpaper or a sanding sponge on a flat surface.

3.) It’s strongly recommended to anneal the edge of your coin ring to be reeded prior to pressing them on. This puts the metal in a softer, more workable state and will make it easier to imprint.

4.) Make sure to use the piece of the impact-resistant urethane pad (included with the “Re-REEDer”) in between your Repair Die / compression press plate and the original reeded-side to protect the existing detail.

5.) I like to press the new reeds on when the coin ring is still cone-shaped, immediately after the folding process and prior to final sizing and finishing. This allows you to easily correct any distortion that may occur to the coin rings’ side walls from over-pressing the new reeds on.

Should that occur, you simply re-anneal your coin ring and put it back into the proper-sized universal folding and reduction die and using a folding cone; fold the coin ring down until the original shape is achieved.
*** NOTE ***
1.) A hydraulic press is required in order to use this tool. The “Re-REEDer” die will NOT work with any ring sizer machine or arbor press. I use a 6-ton hydraulic press that can be purchased from Harbor Freight.

2.) You will need to use a tool such as the Coin Ring Repair Die / Compression Press Plate to place underneath the ram head of the hydraulic press and the top of the coin ring prior to pressing on the reeds. If you don’t already have one, you can find it here:
Be sure to Subscribe to my YouTube channel located under “CoinRingUSA” for coin ring updates, or click on the following link to go directly there:

Thanks, and here’s to your coin ring-making success!